Diagrams & Numbers – E-8000 Knitting Beds & Locks

 E-8000 – Knitting Beds and Locks

     Diagrams and Part Numbers  

PLEASE NOTE:                                                                                All items are priced as single items, not pairs or otherwise.
Pairs must be ordered as 2 of the same Part Number

1 09.155.13 Detent Spring
2 09.161.02 Carrier
3 16.343.03 Pinion
4 30.286.02 Needle Bed Support
5 30.288.03 (8812) Traverse Bar
5 30.292.03 (8809) Traverse Bar
6 30.295.02 Threaded Bar
7 30.298.03 Lowering Guide
8 30.302.03 Lowering Lever
9 30.307.02 Lowering Handle
10 30.309.02 Gliding Piece
11 30.310.02 Fixing Piece White
12 30.312.02 (8812) Coupling Tube
12 30.313.02 (8809) Coupling Tube
13 30.616.03 Lever
14 30.319.02 Gliding Piece
15 30.321.03 Racking Support
16 30.324.02 Spindle
17 30.325.02 Bearing Flange
18 30.326.02 Racking Handle
19 30.327.02 Racking Shaft
20 30.387.02 Special Socket Head Cap Screw M5 x 70
25 90.102.71 Socket Head Cap Screw M5 x 12
26 90.104.17 Socket Head Cap Screw M5 x 70
27 90.337.07 Lens Head Screw D2.9 x 9.5
28 90.337.87 Lens Head Screw M3 x 6
29 90.338.07 Lens Head Screw M4 x 6
31 90.483.71 Hexagonal Head Screw M4 x 8
32 90.632.77 Safety Nut M5
33 90.700.51 Spring Washer D4
34 90.700.61 Spring Washer D5
35 90.750.62 Washer D5.3/10×1
36 90.755.81 Washer D8
37 90.756.01 Washer D13
38 90.765.92 Washer D4
39 90.766.41 Washer D5.2/10×1.5
40 90.941.77 Round Head Pin 3 x 10
41 90.872.74 Set Pin 3 x 40
42 91.030.71 Safety Washer 5 DIN
43 91.030.81 Safety Washer 6 DIN
44 91.031.11 Safety Washer 9 DIN

30.202.00 Needle Bed Front Passap (8812)
30.213.00 Needle Bed Front Pfaff (8812)
2 30.227.02 Profile (8812) Bottom
3 30.229.03 Guide (8812)
4 30.234.02 Profile (8812)
5 30.235.02 Threaded Bar L=159mm/5xM4
6 30.236.03 Chassis (8812) Front
7 30.239.02 Threaded Bar (8812) L=970mm/6xM4
8 30.251.02 Fixing Piece Grey
9 30.253.02 Front Left/back right Passap
9 30.256.02 Front Left/back right Pfaff
10 30.257.02 Side Plate Front right/back left
11 30.265.02 Main Rail front (8812)
12 30.268.02 Guide Rail front right/back left (8812)
13 30.269.02 Guide Rail front left/back right (8812)
14 30.273.02 Holding Rain for Needles (8812) L=1350mm
15 30.275.02 Brake Spring for Needles (8812) L=1306mm
16 30.277.03 Holding Rail for Jacks (8812) L=1620mm
17 30.280.02 Brake Spring for jacks (8812) L-1776mm
18 30.283.02 Hammer Head Screw M3
19 30.284.02 Special Screw M3
20 30.340.02 Needle Scale (8812) right
21 30.241.02 Needle Scale (8812) left
22 90.337.87 Lens Head Screw M3 x 6
23 90.338.17 Lens Head Screw M4 x 8
24 90.632.57 Safety Nut M3
25 90.752.17 Washer D3.2/9×0.8
26 30.258.02 Guiding Piece

30.206.00 M-Needle Bed Back (8812) Passap
30.211.00 M-Needle Bed Back (8812) Pfaff
2 30.227.02 Profile (8812)
3 30.229.03 Guide (8812)
4 30.239.02 Threaded Bar L-970mm/6xM4  (8812)
5 30.240.03 Chassis (8812)
6 30.253.02 Side Plate front left/back right Passap
6 30.256.02 Side Plate front left/back right Pfaff
7 30.257.02 Side Plate front right/back left
8 30.259.01 VM-Main Rail Complete (8812)
9 30.268.02 Guide Rail front right/back left (8812)
10 30.269.02 Guide Rail front left/back right (8812)
11 30.273.02 Holding Rail for needles L=1350mm
12 30.275.02 Brake Spring for needles L-1306mm
13 30.277.03 Holding Rail for Jacks L=1620mm
14 30.280.02 Brake Spring for Jacks (8812) L=1776mm
15 30.283.02 Hammer Head Screw M3
16 30.284.02 Special Screw M3
17 30.295.02 Threaded Bar L=59mm/3xM4
18 90.338.17 Lens Head Screw M4 x 8
19 90.632.57 Safety Nut M3
20 90.752.17 Washer D3.2/0x0.8

30.220.01 VM-Needle Bed Section with steel guides
1 11.777.02 Latch Needle
2 30.221.02 Needle Bed Section without guides
3 30.222.02 Knock Over Comb E-88
4 30.223.02 Needle Guide E-8
5 30.224.02 Jack Guide E-8
6 30.225.02 Jack E-8
7 30.230.02 Bed Section Union
8 30.283.02 Hammer Head Screw M3
9 30.284.02 Special Screw M3
10 90.632.57 Safety Nut M3

30.406.00 Cam Box Front
1 30.448.01 E-10 VM-Cam Body right
2 30.449.01 E-10 VM-Cam Body left
3 05.188.02 Handle Support
4 05.228.03 Pusher Cam Left
5 05.229.03 Pusher Cam Right
6 05.234.02 Cam Slider
7 09.064.11 E-11 VM-Cam Carrier
8 09.338.12 Cam Slider
9 09.345.22 Rejector Left
10 09.346.22 Rejector Right
11 09.347.02 Auxiliary Rejector Left
12 09.348.02 Auxiliary Rejector Right
13 09.388.02 Pressure Spring D7 x 12.4
14 09.412.22 Cam Control Fork
15 10.398.02 Deviating Plate
16 15.292.02 Tension Spring D4.2 x 17
17 16.133.03 Catch Lever
18 16.135.03 Notch lever
19 16.138.03 Program Slider
20 16.143.02 Bush Large
21 16.144.02 Cam Plate
22 16.152.02 Pressure Spring D6.5 x 10
23 30.654.02 Axle
24 16.158.02 Guide Bolt
25 16.165.02 Axle for N-X Lever
26 16.166.02 Special Cylinder Screw M3
27 16.487.02 Pressure Spring D3.5 x 9.5
28 30.435.01 E-13 VM-Commanding Device E-8800
29 30.441.01 E-14 VM-Adjustment Support
30 30.444.00 E-22 Row Counter
31 30.450.03 Cam Box Plate Front
32 30.456.01 E-12 VM-Control Plate Back
33 30.480.02 Intermediary Plate
34 30.481.02 Auxiliary Guide Left
35 30.482.02 Auxiliary Guide Right
36 30.483.02 Main Guide Left
37 30.484.02 Main Guide Right
38 30.486.02 Control Knob
39 30.487.02 Readjusting Lever
40 30.514.02 Earth Spring
41 30.518.02 Bolt
42 30.601.01 E-08 VM-Selector Support packed
43 30.743.02 Carrier Cable Front
50 90.242.31 Lens Head Screw M4 x 12
51 90.250.07 Lens Head Screw M3 x 6
52 90.336.07 Lens head Screw D2.9 x 13
53 90.337.07 Lens Head Screw D2.9 x 9.5
54 90.412.01 Cylinder Screw M3 x 4
55 90.412.17 Cylinder Screw M3 x 5
56 90.412.32 Cylinder Screw M3 x 8
57 90.427.81 Cylinder Screw M3 x 6
58 90.428.01 Cylinder Screw M3 x 8
59 90.483.71 Hex Head Screw M4 x 8
60 90.632.57 Safety Nut M3
61 90.700.31 Spring Washer 3.2/5.8×0.8
62 90.715.31 Spring Washer A3
63 90.765.92 Distance Washer D4.2/10×1
64 90.767.81 Distance Washer D3.2/8×1
65 91.030.51 Safety Washer 3.2 DIN
66 91.030.61 Safety Washer 4DIN

30.408.00 M-Cam Box Back
1 30.448.01 VM-Cam Body Right
2 30.449.01 VM-Cam Body Left
3 05.188.02 Handle Support
4 05.228.03 Pusher Cam Left
5 05.229.03 Pusher Cam Right
6 05.234.02 Cam Slider
7 09.064.11 E-11 VM-Cam Carrier
8 09.338.12 Cam Slider
9 09.345.22 Rejector Left
10 09.346.22 Rejector Right
11 09.347.02 Auxiliary Left
12 09.348.02 Auxiliary Right
13 09.388.02 Pressure Spring D7.12.4
14 09.412.22 Cam Control Fork
15 10.398.02 Deviating Plate
16 15.292.02 Tension Spring D4.2 x 17
17 16.133.03 Catch Lever
18 16.135.03 Notch Lever
19 16.138.03 Program Slider
20 16.143.02 Bush Large
21 16.144.02 Cam Plate
24 16.158.02 Guide Bolt
25 16.165.02 Axle for N-N Lever
26 16.166.02 Special Cylinder Screw M3
27 16.487.02 Pressure Spring D3.5 x 9.5
28 30.435.01 E-13 VM-Commanding Device E-8800
29 30.441.01 E-14 VM-Adjustment Support
31 30.451.03 Cam Box Plate Back
32 30.456.01 E-12 VM-Control Plate Back
34 30.481.02 Auxiliary Guide Left
35 30.482.02 Auxiliary Guide Right
36 30.483.02 Main Guide Left
37 30.484.02 Main Guide Right
40 30.514.02 Earth Spring
41 30.518.02 Bolt
42 30.601.01 E-08 VM-Selector Support packed
43 30.744.02 Carrier Cable Back
51 90.250.07 Lens Head Screw M3 x 6
52 90.336.07 Lens Head Screw D2.9 x 13
53 90.337.07 Lens Head Screw D2.9 x 9.5
54 90.412.01 Cylinder Screw M3 x 4
55 90.412.17 Cylinder Screw M3 x 5
56 90.412.32 Cylinder Screw M3 x 8
57 90.427.81 Cylinder Screw M3 x 6
58 90.428.01 Cylinder Screw M3 x 8
59 90.483.71 Hex Head Screw M4 x 8
60 90.632.57 Safety Nut M3
61 90.700.31 Spring Washer D3
62 90.715.31 Spring Washer A3
63 90.765.92 Distance Washer D4.2/10×1
64 90.767.81 Distance Washer D3.2/8×1
65 91.030.51 Safety Washer 3.2 DIN
66 91.030.61 Safety Washer 4 DIN
70 09.570.22 Axle Carrier
71 09.572.02 Holding Cleat
72 30.447.01 VM-Carrier Driver
73 30.520.00 E-16 M Lock Unit
74 30.590.01 E-15 VM-Feeder Drive
75 30.719.03 Plug Circuit Board
76 90.337.97 Lens Head Screw M3 x 10

 

1 30.449.03 Handle
2 30.470.02 Carrier Hood Front
3 30.475.02 Position Button
4 30.476.02 Stitch Length Button
5 30.477.02 Grip
6 30.486.02 Control Knob
7 30.487.02 Readjusting Lever
8 30.471.02 Carrier Hood Back

1 30.601.01 VM-Selector Support packed
2 30.615.03 Magnetic Cam Left
3 30.316.03 Magnetic Cam Right
4 30.630.02 Selector Support
5 30.641.02 Base Cam
6 30.650.02 Coil Axle
7 30.660.02 Magnet Outside
8 30.661.02 Magnet Centre Right
9 30.662.02 Magnet Centre Left
10 30.820.01 VM-Carrier Circuit Board packed
11 30.740.02 Coil
12 91.030.41 Safety Washer 2.3 DIN
13 05.196.03 Light Barrier Brush

1 30.449.01 VM-Cam Body Left E-6000
2 30.448.01 VM-Cam Body Right E-6000
3 30.489.02 Cam Body Left E-6000
4 30.488.02 Cam Body Right E-6000
5 05.160.02 Reversing Plate Left E-6000
6 05.161.02 Pusher Lowering Cam Right E-6000
7 05.162.02 Pusher Lowering Cam Left E-6000
8 05.163.02 Rejector Left E-6000
9 05.164.02 Rejector Right E-6000
10 05.165.02 Reversing Cam E-6000
11 05.166.02 Pusher Raising Cam Left E-6000
12 05.167.02 Pusher Raising Cam Right E-6000
13 05.168.02 Separating Cam Left E-6000
14 05.169.02 Separating Cam Right E-6000
15 05.170.02 Protection Cam Left  E-6000
16 05.171.02 Protection Cam Right  E-6000
17 05.172.02 Reversing Plate Right  E-6000
18 05.236.02 Double Rejector Left E-6000
19 05.237.02 Double Rejector Right E-6000
20 05.238.02 Pusher Return Cam Left E-6000
21 05.239.02 Pusher Return Cam Right E-6000
22 90.330.81 Countersunk Parker Screw D 2.9 c 9.5

1 09.064.11 VM-Cam Carrier
2 09.317.33 Cam Carrier
3 09.380.02 Outside Flap Right
4 09.381.02 Outside Flap Left
5 09.382.02 Inside Flap Right
6 09.383.02 Inside Flap Left
7 09.384.12 Axle
8 09.386.02 Torsion Spring Right
9 09.387.02 Torsion Spring Left
10 91.030.41 Safety Washer 2.3 DIN

1 30.456.01 VM-Control Plate E-88
2 30.458.03 Lowering Cam E-88
3 30.462.03 Control Plate Back E-88
4 11.829.02 Pulling Spring
5 90.766.71 Washer 5.2/8 x 0.9
6 91.032.51 Special Safety Washer 4 DIN

1 30.435.01 VM-Commanding Device E-8800
2 09.450.02 Lateral Axle
3 09.451.02 Guiding Bush
4 09.468.02 Driving Axle
5 16.210.02 Base Plate
6 05.185.02 Curved Slider E-1 (U)
7 16.212.02 Curved Slider 2 (G)
8 05.186.02 Curved Slider E 3 (S)
9 16.214.02 Curved Slider 4 (E)
10 05.187.02 Curved Slider E-5 (O)
11 16.216.02 Curved Slider 6 (C)
12 16.217.02 Curved Slider 7 (L+B)
13 16.218.02 Curved Slider 8 (K+A)
14 16.219.02 Intermediary Plate
15 16.220.02 Commanding Axle
16 16.223.02 Ratchet
17 16.224.02 Operating Slider
18 30.438.03 Switch Lever
19 16.228.02 Stop Washer
20 91.030.51 3.2 DIN

+

1 30.441.01 VM-Adjustment Support
2 09.580.02 Axle
3 16.125.03 Adjustment Support
4 16.130.02 Adjustment Lever
5 16.147.02 Pressure Spring D11 x 9
6 30.496.02 Cam Disc
7 30.516.02 Sleeve
8 30.517.02 Bolt
9 90.632.47 Safety Nut M4
10 91.030.51 Safety Washer 3.2 DIN
11 30.541.02 Washer D4.3/12×0.8

1 30.590.01 VM-Feeder Drive
2 09.701.22 Drive Shaft
3 09.702.22 Auxiliary Wheel
4 09.705.12 Driving Wheel
5 09.707.32 Driver Plate
6 09.711.02 Sliding Disc
7 30.591.02 Driver Sleeve L=33
8 30.592.02 Pressure Spring D9.8×22
9 30.593.03 Crank Lever
10 30.598.02 Guiding Piece
11 90.750.02 Washer 2.7/6.5×0.5
12 91.030.31 Safety Washer 1.9 DIN
13 91.030.51 Safety Washer 3.2 DIN
14 91.030.81 Safety Washer 6 DIN

1 30.520.00 M-Lock Unit
2 09.677.02 Damper
3 09.680.13 Brush
4 14.834.02 Excentric Bolt
5 14.838.02 Torsion Spring
6 14.881.02 Support
7 14.882.02 Pressure Spring
8 14.889.02 Auxiliary Lever
9 14.899.12 Brush Holder Back
10 14.901.02 Face Cam
11 14.903.02 Special Screw M3
12 14.912.02 Distance Washer
13 30.522.01 VM-Closing Lever
14 30.530.03 Stripper Carrier
15 30.535.03 Switch Lever
16 30.540.02 Axle
17 30.541.02 Distance Washer D4.3/12×0.8
18 30.543.02 Guiding Piece
19 30.547.02 Stripper Slider
20 30.548.03 Stripper Plate
21 30.561.03 Support
22 30.566.02 Distance Washer D3.2/10×0.2
23 30.567.02 Distance Washer D3.2/10×0.8
24 30.568.03 Closing Lever
25 30.574.03 Lever MS 8000
26 30.580.02 Torsion Spring
27 30.581.02 Articulation Lever
28 30.584.03 Front Brush
29 90.223.87 Special Screw M6 x 16
30 90.337.07 Lens Head Screw D2.9×9.5
31 90.350.01 Parker Screw D2.2×6.5
32 90.605.53 Hexagon Nut M4
33 90.605.72 Hexagon Nut M6
34 90.632.47 Safety Nut M4
35 90.700.51 Spring Washer D4
36 90.700.71 Spring Washer D6
37 90.750.02 Washer D2.7/6.5×0.5
38 90.767.24 Distance Washer D7.1/18×2.0
39 90.769.14 Distance Washer D4.2/10×1.25
40 91.030.31 Safety Washer 1.9 DIN
41 91.030.41 Safety Washer 2.3 DIN
42 91.030.51 Safety Washer 3.2 DIN

1 30.335.01 VM-Edge Spring 6 leaves
2 30.336.02 Edge Spring 6 leaves
3 09.836.12 Lower Part
4 09.838.02 Pressure Spring
5 09.839.02 Pressure Bolt
6 16.049.02 Push Button
7 90.337.07 Lens Head Screw D2.9×9.5

1 30.150.00 M=Yarn Tensioner
2 14.760.05 Magnet
3 30.156.01 VM-Support with Tension Discs
4 30.160.02 Support
5 30.162.02 Tension Knob Left
6 30.164.02 Tension Knot Right
7 30.166.02 Buffer for Tension Arms
8 30.168.02 Tension Knob Axle
9 30.169.02 Tension Spring
10 30.170.02 Tension Arm Left
11 30.172.02 Tension Arm Right
12 30.174.02 Yarn Guide
13 30.175.03 Junction Circuit Board
14 30.178.02 Pressure Spring D5.5×45
15 30.179.02 Pressure Spring D5.4×28
16 31.064.02 Washer D4.2/16×1.5
17 90.337.07 Lens Head Screw D2.9×9.5
18 91.030.51 Safety Washer 3.2 DIN
19 91.030.81 Safety Washer 6 DIN
20 30.193.03 Spiral Cable
21 10.910.03 FCC Cable 6 poles L=1200mm
22 30.180.03 FCC Cable 4 poles L=2020mm
23 30.181.03 FCC Cable 4 poles L=450mm
24 30.194.03 FCC Cable 6 poles L=2020mm

1 30.156.01 VM-Support with Tension Discs S-8000
2 14.970.02 Notched Disc
3 15.754.02 Support
4 15.761.12 AxleD6x66.4
5 15.762.02 Brake Disc Large
6 15.764.02 Axle D3x26
7 15.766.02 Pressure Spring D16.7×15
8 15.769.02 Intermediary Plate
9 15.770.02 Brake Disc Small
10 16.403.02 Double Eyelet Front
11 30.182.02 Adjustment Knob Right
12 30.184.02 Adjustment Knob Left
13 30.186.02 Curved Disc
14 30.188.02 Eyelet of Support S8
15 90.302.31 Countersunk Screw M3x8
16 90.428.01 Cylinder Screw M3x8
17 90.600.57 Hexagon Nut M3
18 91.030.31 Safety Washer DIN 1,9
19 91.030.71 Safety Washer DIN 5

1 30.700.03 M-Control Unit – Passap
1 30.701.03 M-Control Unit – Pfaff
2 30.705.02 Cover Passap
2 30.747.02 Cover Pfaff
3 30.708.02 Cover Bottom
4 30.709.02 Display Window
5 30.816.01 VM-Key Pad packed
6 30.821.01 VM-Key Board Printed Circuit packed
7 30.822.01 VM-Interface Circuit Board packed
8 30.823.01 VM-Processor Circuit Board packed
9 30.825.01 VM-Display 4×20 characters packed
10 30.730.01 VM-Memory Module E8812VH
11 30.741.03 Key Board Cable
12 30.742.03 Interface Cable
13 90.332.07 Lens Head Screw D2.2×4.5
14 90.337.07 Lens Head Screw D2.9×9.5 TORX
15 30.728.02 Voltage Converter 230V/50-60 HZ
15 30.729.02 Voltage Converter 120V/60 HZ

1 30.712.01 VM-Swing Arm
2 30.711.02 Swinging Arm
3 30.714.02 Swinging Arm Support
4 30.715.02 Swing Arm Axle
5 90.695.69 Pressure Spring D9.8×40
6 90.736.37 Washer D13/30×3
7 91.030.91 Safety Washer 7 DIN

1 30.444.00 M-Row Counter
2 16.309.03 Spring Plate
3 16.310.03 Sliding Plate
4 16.311.12 Row Counter Support
5 16.314.12 Ratchet
6 16.316.02 Readjusting Piece
7 16.317.02 Excentric Piece
8 16.318.02 Figure Wheel
9 30.479.02 Switch Lever
10 16.230.02 Base Plate
11 30.486.02 Control Knob
12 16.323.02 Tension Spring D2x18
13 16.324.02 Tension Spring D2.9×9.6
14 16.325.02 Tension Spring D2.6×12.6
15 30.487.02 Readjusting Lever
16 91.030.21 Safety Washer 1.5 DIN

1 30.210.01 VM-Accessories
2 30.192.03 Earth Cable L=700mm
3 30.295.02 Threaded Bar M4/L=59mm
4 30.310.02 Fixing Piece White
5 90.104.17 Socket Head Cap Screw M5x70
6 90.332.67 Lens Head Screw D3,5×13
7 90.337.07 Lens Head Screw D2.9×9.5
8 90.338.17 Lens Head Screw M4x8
9 90.414.11 Cylinder Head Screw M4x25
10 90.483.71 Hexagonal Head Screw M4x8
11 90.700.51 Spring Washer D4
12 90.700.67 Spring Washer D5
13 90.765.92 Washer D4.2/10×1
14 90.766.41 Washer D5.2/10×1.5
15 91.030.61 Safety Washer 4 DIN

1 30.961.02 Pattern Ruler 1:1 E-8
2 11.777.02 Latch Needle E-8
3 30.225.02 Jack E-8
4 30.962.02 Double Ended Bodkin E-8
5 30.965.02 Blue Tool
6 30.525.03 Presser Foot Lilac
7 30.526.03 Presser Foot Black
8 31.048.01 Feeder E 8 Grey
9 30.960.02 Jack Slider

1 03.728.02 Spirit Level
2 03.688.02 Screw Driver TORX T10
3 03.690.02 Screw Driver TORX T15
4 03.691.02 Screw Driver TORX T20
5 03.604.02 Box Spanner 5.5mm
6 03.721.01 Set of control gauges for needle beds E-8
7 03.720.02 Control Gauge for presser foot
8 03.025.02 Oil Tube 20cc
9 03.642.02 Bellodor Oil 0.5 litre
10 03.643.02 Bellodor Oil 1 litre
11 03.644.02 Bellodor Oil 2 litres
12 07.306.22 Dust Brush